#TARGET CROSSHAIRS HOW TO#
#TARGET CROSSHAIRS CODE#
#TARGET CROSSHAIRS PROFESSIONAL#

All you have to do is turn your turret until it’s in the center and then tighten it down with screws or bolts on either side of where your cross-hair meets. 3) Dot Reticle:Ī dot reticle is a lot easier to adjust than the others. All you have to do is move one line until it covers up where the cross-hair meets and then tightens down the adjustment screws. When you adjust this kind of rifle scope, you will see two lines on your screen next to each other. This type of scope crosshair is the best for adjusting because it has a duplex reticle.

#TARGET CROSSHAIRS HOW TO#

This is because they have experience in fixing original rifle scopes and know how to do it perfectly.

#TARGET CROSSHAIRS PROFESSIONAL#

If you are using an original reticle, getting a professional is the best way to fix your scope crosshair. This type of scope crosshairs can be complicated to adjust because so many variations exist. Some of them we have mentioned below: 1) Original Reticle: There are different types of scope crosshair. The type of scope crosshair you have on your rifle will determine how to fix a scope crosshair.

Make sure the whole lens is clean and dry before putting new crosshairs on your scope.

Cleaning your rifle scope is a great way to ensure you can keep using it without any problems.

Reattach it as instructed in How to Fix a Scope Crosshair and use an extra layer of tape for good measure.

Apply some new adhesive in this area, then put it back on the scope crosshair.

Use a small flathead screwdriver or blade to pry off any remaining glue pieces around where you cleaned with the tape.

Once your crosshair is removed, use a hairdryer to heat up the adhesive and melt it.

Clean off any residue left behind by the adhesive on the bottom of the crosshair this will make future removal easier.

Use a small piece of tape to remove the crosshair from your scope.

Tips For Maintaining Your Scope Crosshair Step Seven:Īim the crosshairs at your target and once you have an accurate reading, tighten down the screws. Place your crosshairs by putting them on top of a target or in some other way to get an accurate reading of where they are aiming when you pull back this trigger. Tighten these screws down now nice and tight! Step Six: Place the second ring onto the scope and line it up with the screw holes. It’s a good idea to loosely tighten these now so that they don’t move while you’re working on them. Place one ring onto your rifle and line up where you want to mount it, then place the screws in their respective holes. Lift off one side, then gently tap on top until it separates. Remember the orientation of the screws and how they will need to go back into place when you’re finished. To remove the scope rings from your rifle, unscrew the screws that are holding them in place. This will make it easier for you and your tools to work on and allow you to see any dust obstructing your view of the target. The first step is to clean the rifle scope thoroughly. Instructions: How to Fix a Scope Crosshair Step One: This article also covers the importance of keeping your scope clean to work correctly and what could cause a crooked crosshair. If you’ve noticed your crosshair is not straight, this article will show you how to fix a scope crosshair on your own. Java is a registered trademark of Oracle and/or its affiliates.Scope crosshairs are an important part of a rifle scope and must be in good working order. For details, see the Google Developers Site Policies.

#TARGET CROSSHAIRS CODE#

Set crosshair opacity to opacity_number on selectionĮxcept as otherwise noted, the content of this page is licensed under the Creative Commons Attribution 4.0 License, and code samples are licensed under the Apache 2.0 License.

Here's a complete web page that creates the above chart, with the Hover over the points below, or select them, to see crosshairs: In your charts, your users will then be able to target a singleĬrosshairs can appear on focus, selection, or both. When you, as a chart creator, enable crosshairs Crosshairs are thin vertical and horizontal lines centered on aĭata point in a chart.

Target crosshairs